Electrician On CallEtobicoke

Electrician for Etobicoke homes

Electrical Problem? Get the Right Help.

Troubleshooting, repairs and electrical service requests in Etobicoke.

Request service How it works

No forms, no call centre. You describe the problem, we confirm scope and timing before any visit.

Electrician kneeling at the side of a house with beige vinyl siding, fitting an outdoor receptacle with a cordless drill; a clamp meter rests on the deck boards
Fitting an exterior receptacle on vinyl siding; the weatherproof cover is still to go on. Shown in progress.

What’s happening?

Pick the closest match. Each one opens a plain explanation of the usual causes, what to do right now and what the repair tends to involve.

No powerA room, a floor or the whole house. Breaker trippingTrips again after a reset, or will not reset. Outlet problemDead, loose, warm, or sparking at the plug. Lights or fixturesFlicker, buzz, dim, or a fixture that quit. Something elseDescribe it and we will say whether it is something we handle.

Before anything else: is it safe?

Most electrical faults are inconvenient rather than dangerous, but a few are the other way around. Two rules cover nearly every situation.

Stop using it

If an outlet, switch, cord or fixture is warm, discoloured, buzzing or smells of heat, stop using it and unplug whatever is on it. If you can reach the panel safely, switch off the breaker for that circuit and leave it off. Do not open the panel, the device or the fixture, and do not attempt a repair on a live circuit. That part is for a qualified professional.

If there is real danger, call 911

Flames, smoke you can see, a burning smell you cannot trace, or a shock from a tap, appliance or wall: get everyone out and call 911. Property can be repaired afterwards. Everything on this site is for once the danger has passed.

Repairs and troubleshooting

Six kinds of work cover most of what we are asked for in Etobicoke. Each says what it includes, not more.

  • Breaker and fuse problems

    Breakers that trip again after a reset, will not reset or feel loose; fuses that keep blowing. We find the cause before anything is reset again.

  • Dead outlets and switches

    An outlet that stopped working, a switch that does nothing or works some of the time, a plug that falls out of the wall. GFCI and tamper-resistant replacements included.

  • Light and fixture faults

    Flickering, buzzing on a dimmer, a fixture that went dark, pot lights that drop out. Repair or replacement of interior and exterior fixtures.

  • Electrical diagnostics

    Measured, not guessed. Voltage, current and continuity are checked with a meter to locate the fault before any part is replaced.

  • Safety-related repairs

    Warm or scorched devices, buzzing from the panel, shocks or tingles, outlets near water without GFCI protection, smoke alarms past their date.

  • Small installations

    Exterior receptacles, security floodlights and wall lights, smoke and CO alarm replacement, dryer and range connections, hot tub disconnects.

All services and what they include

What a diagnosis actually looks like

A fault usually shows up as a symptom in one place and has its cause in another. A meter reading says where to look next. These photos show that stage of the job: readings being taken, covers off, nothing finished yet.

Digital multimeter standing on a counter with its probes in a receptacle whose cover plate has been removed; the display reads 45.24 volts AC
DiagnosticVoltage check at a receptacle with the cover plate off. A reading like this is a clue in a diagnosis, not a finished repair.
Hand holding a digital multimeter in front of a wall receptacle in a wood-panelled room, one probe inserted; the display reads 95.3 volts AC
DiagnosticMeter on a receptacle during fault finding. A reading well below the 120 V expected points to a connection problem that still has to be located.
Close-up of black, red and white conductors with a green ground landed on the terminal block of an appliance, with a strain relief below
Cover removedConductors landed on an appliance terminal block, photographed with the access cover removed.
Smoke alarm unhooked from its ceiling mounting plate and hanging by its wiring harness below a textured ceiling with the box visible
In progressHardwired smoke alarm dropped from its mounting plate to reach the harness. Ceiling box open during replacement; shown in progress.
Symptoms and their usual causes

How a service call works

Three stages, no surprises in between.

  1. Tell us what is happening

    Which room, what stopped or started doing something odd, and since when. A photo of the device or the panel label helps.

  2. We confirm scope and timing

    You get a plain reply saying what the visit will cover and when it can happen. No visit is booked until you have agreed to both.

  3. Diagnose, repair, test

    Meter first, cover off only when the readings say so, then the repair. The circuit is loaded and re-measured before we call it done.

The full process

Where we work

Based on Panorama Court in north Etobicoke and working across the borough. The neighbourhoods closest to us are listed below; if yours is in Etobicoke but not on the list, ask.

  • Rexdale
  • Thistletown
  • Smithfield
  • West Humber–Clairville
  • Humberwood

Etobicoke is in Toronto Hydro territory. If the whole street is dark, that is their call to answer, and their outage map is the quickest check.

Common questions

Is this an emergency service?

No. If there is fire, smoke or a shock, call 911 first. A request sent to us is answered when we are free, and we confirm timing before any visit rather than promising one.

Should I reset a breaker that tripped?

Once is reasonable, after unplugging whatever was running. If it trips again, leave it off; the second trip is the fault telling you it is still there, and repeated resets make it harder to find and can wear the breaker. Why breakers trip.

An outlet is dead but no breaker tripped. Why?

Often a GFCI outlet elsewhere on the same circuit has tripped; check bathrooms, kitchen, garage and outside. Otherwise it is usually a loose connection upstream in another box. That is a heat source, so it should be repaired rather than lived with. More on outlet faults.

Does a small repair need an ESA inspection?

Replacing a device like for like, such as a receptacle, switch or light fixture, typically does not need a notification to the Electrical Safety Authority. New circuits, panel work and wiring for a hot tub or similar do. We tell you which category a job falls in before it starts.

Can you tell me what is wrong from a description?

Sometimes we can narrow it to two or three likely causes, and we will say so. A real diagnosis needs a meter at the fault, which is why we confirm scope rather than quote a fix sight unseen.

What does a service call cost?

It depends on how long the fault takes to find and what, if anything, needs replacing. You hear the scope before work starts, and if the first look turns up something bigger, you hear about that before it continues.

Request service

Tell us what is happening and where. We reply to confirm what the visit covers and when it can happen.

21 Panorama Ct
Etobicoke, ON M9V 4E3
Request service Check the symptom first
Request service